TECHNICAL DATA / DEVICE SELECTION
RM200Technical datasheet
Two independently controlled relay outputs, LoRaWAN connectivity and local pushbutton control in a compact DIN-rail module.
- Relay channels
- 2 independent
- Rated current
- 10 A / channel
- Mounting
- 35 mm DIN rail
- Communication
- LoRaWAN
Product overview
The RM200 is a mains-powered relay module for remotely switching two independent outputs over LoRaWAN. Each channel has local pushbutton control, allowing an operator to override the remote command at the device.
The 36 mm-wide enclosure mounts on a standard 35 mm DIN rail. The documented RM200 edition is identified by part number P1002003 and firmware V1.1.0.
Key capabilities
- Independent switching: two isolated relay channels, each rated at 10 A.
- Local operation: individual channel buttons select automatic control or manual override.
- Configurable recovery: choose the default relay state after restart and the timeout state for a communication watchdog alarm.
- Flexible configuration: local configuration over Bluetooth Low Energy or remote configuration through LoRaWAN downlinks, as described in the RM200 overview.
- Device monitoring: channel indication, network-quality feedback and internal temperature protection.
Electrical specifications
| Parameter | RM200 |
|---|---|
| Power supply | 230 VAC mains, as described in the device overview and power-supply chapter |
| Relay channels | 2, independently controlled |
| Rated current, per channel | 10 A |
| Maximum switching current | 10 A AC |
| Maximum switching voltage | 250 V AC |
| Contact resistance | Maximum 100 mΩ |
| Connections described in installation chapter | Common (C) and normally open (NO), per relay |
| Terminal conductor size | 0.5–2.5 mm² |
Select the load and its protection for the installation. A current rating alone does not establish suitability for every motor, capacitive load or inrush current.
Communication & configuration
| Parameter | Published specification |
|---|---|
| LoRaWAN version | 1.0.4 |
| Radio region | EU 863–870 MHz |
| Maximum transmit power | 14 dBm |
| Activation | Over-the-air activation (OTAA) |
| Application port | 50 |
| Antenna | Built in |
| Local configuration | Bluetooth Low Energy, using the device application |
| Remote configuration | LoRaWAN downlinks |
The LoRaWAN chapter describes mains-powered devices as Class C. Use the device label and firmware information when provisioning the network server. The RM200 decoder provides the separate payload integration reference.
Mechanical & environmental
| Parameter | Published RM200 manual value |
|---|---|
| Mounting | Standard 35 mm DIN rail |
| Enclosure width | 36 mm |
| Intended environment | Indoor use |
| Enclosure protection | IP20 |
| Weight | 102 g |
| Operating temperature | −20 to +60 °C |
| Storage temperature | −40 to +85 °C |
| Operating humidity | Maximum 85% RH, non-condensing |
| Altitude | 0–2,000 m |
Values in this draft follow the GitBook RM200 edition. Full enclosure dimensions and a dimensioned drawing are awaiting hardware review.
Model identification & ordering
| Item | Identification |
|---|---|
| Model | RM200 |
| Part number | P1002003 |
| Firmware covered by source manual | V1.1.0 |
| EAN | 8720892076755 |
| Country of origin | The Netherlands |
| Package contents | DIN-rail module and quick-start manual |
Confirm the model code on the label before using this document. Other RCM, RPB and OCMD2 models have their own configurations and need their own technical specifications.
Related documentation
Document sources & revision
DS-RM200 · Revision 0.1 · 23 September 2026 · Technical review pending.
Based on the published device overview, technical specifications, installation chapter and application operation. Installation procedures belong in the separate user guide.